[oopic] Re: owire2, owire2c and ofanout2 cannot use in oopic complier 6 why.....help(4)

Dear sir,

I have tried the Owire2 but oopic-R only turn only the LED no flash.
Pls, help

Michael

--- In oopic@yahoogroups.com, ooPIC Tech Support <dennis.clark@...>
wrote:
>
> You have linked your clock to the oWire input, you have not linked
> anything to the oWire.ProcessClock. I recommend that you don't use
> oWire2C and simply use oWire2. I have found little reason to use
the
> "C" options unless you are needed a special synchronization to
another
> object. To copy across the oWire using oWireC you need to toggle
the
> ProcessClock flag. I repeat, simply use oWire2 and it should work.
>
> DLC
>
> aibomc wrote:
> > Dear Sir,
> >
> > I write the these two case of program and download to oopicR
B2.2+ by
> > complier 6.1.1. Unfortunately, I cannot success on it. however,I
> > success the case(1) program by complier 5.0.1, the oopic-R could
make
> > the two LEDs to flash.
> >
> > Could you kindly check this matter? thanks
> >
> > *Case(1)
> > Dim W As New oFanout(2)
> > Dim LED_1 As New oDIO1
> > Dim LED_2 As New oDIO1
> > Dim a As New oClock
> >
> > Sub Main()
> >
> > LED_1.IOLine = 6
> > LED_1.Direction = cvOutput
> > LED_2.IOLine = 5
> > LED_2.Direction = cvOutput
> >
> > a.Rate = 200
> > W.Input.Link(a)
> > a.Operate = cvTrue
> >
> > W.Output1.Link(LED_2)
> > W.Output2.Link(LED_1)
> > W.Operate = cvTrue
> >
> > End Sub
> >
> > Result:
> > Case(1) Program is only turn on the two LED in oopic-R.
> >
> > *Case(2)
> > Dim W As New oWire2C
> > Dim LED_1 As New oDIO1
> > Dim LED_2 As New oDIO1
> > Dim a As New oClock
> >
> > Sub Main()
> >
> > LED_1.IOLine = 6
> > LED_1.Direction = cvOutput
> > LED_2.IOLine = 5
> > LED_2.Direction = cvOutput
> >
> > a.Rate = 200
> > W.Input.Link(a)
> > a.Operate = cvTrue
> >
> > W.Output1.Link(LED_2)
> > W.Output2.Link(LED_1)
> > W.Operate = cvTrue
> >
> > End Sub
> >
> > Result:
> > Case(2) the two LED no any respond.
> >
> > Thank you for your kindly support
> >
> > Michael
> >
> > --- In oopic@yahoogroups.com, "aibomc" <aibomc@> wrote:
> >
> >> --- In oopic@yahoogroups.com, "aibomc" <aibomc@> wrote:
> >>
> >>> Dear sir,
> >>>
> >>> Actually, I tried the oFanOut2,oWire2 and oWire2c, it does work
> >>>
> > at
> >
> >>> oopic V6.
> >>> Pls, help
> >>>
> >>> Michael
> >>> --- In oopic@yahoogroups.com, ooPIC Tech Support
<dennis.clark@>
> >>> wrote:
> >>>
> >>>> Please check out the manual and example programs. This line:
> >>>> Dim W As New oFanOut2/OWire2/Owire2c
> >>>> will not compile. Try this instead:
> >>>> Dim W As New oFanOut2
> >>>>
> >>>> DLC
> >>>>
> >>>> aibomc wrote:
> >>>>
> >>>>> Dear Sir,
> >>>>>
> >>>>> I write the following program by oopic complier Ver6 using
> >>>>>
> > the
> >
> >>>>> OFanout, Owrie and owire2c
> >>>>> However, It cannot seccess in Window XP.
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >
*********************************************************************
> >
> >>>>> 'ooPIC Version: ooPIC R B2.2
> >>>>>
> >>>>> The oClock Object generates specific clock rate To LED-1 &
> >>>>>
> > LED-2
> >
> >>>>> interface by oFanOut2
> >>>>>
> >>>>> ' *********** ************** ------> LED-1
> >>>>> ' *Oclock(a)*----->*OFanout2 (w)*
> >>>>> ' *********** ************** ------> LED-2
> >>>>>
> >>>>>
> >>>>> Dim W As New oFanOut2/OWire2/Owire2c
> >>>>> Dim LED_1 As New oDIO1
> >>>>> Dim LED_2 As New oDIO1
> >>>>> Dim a As New oClock
> >>>>>
> >>>>> Sub Main()
> >>>>>
> >>>>> LED_1.IOLine = 6
> >>>>> LED_1.Direction = cvOutput
> >>>>> LED_2.IOLine = 5
> >>>>> LED_2.Direction = cvOutput
> >>>>>
> >>>>>
> >>>>> a.Rate = 200
> >>>>> W.Input.Link(a)
> >>>>> a.Operate = cvTrue
> >>>>>
> >>>>>
> >>>>> W.Output1.Link(LED_2)
> >>>>> W.Output2.Link(LED_1)
> >>>>> W.Operate = cvTrue
> >>>>>
> >>>>>
> >>>>> End Sub
> >>>>>
> >>>>>
> >
*********************************************************************
> >
> >>>>> Could you kindly reply my problem?
> >>>>>
> >>>>> Thank you for your concern
> >>>>>
> >>>>> Michael
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>> Yahoo! Groups Links
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>> --
> >>>> ------------------------------------------------------
> >>>> Dennis Clark ooPIC Tech Support
> >>>> www.oopic.com
> >>>> ------------------------------------------------------
> >>>>
> >>>>
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
> --
> ------------------------------------------------------
> Dennis Clark ooPIC Tech Support
> www.oopic.com
> ------------------------------------------------------
>

Yahoo! Groups Links

<*> To visit your group on the web, go to:

http://groups.yahoo.com/group/oopic/

<*> Your email settings:
Individual Email | Traditional

<*> To change settings online go to:

http://groups.yahoo.com/group/oopic/join

(Yahoo! ID required)

<*> To change settings via email:
mailto:oopic-digest@yahoogroups.com
mailto:oopic-fullfeatured@yahoogroups.com

<*> To unsubscribe from this group, send an email to:
oopic-unsubscribe@yahoogroups.com

<*> Your use of Yahoo! Groups is subject to:

http://docs.yahoo.com/info/terms/