Chinese / English) version. Firstly, I use either serial cable or
perallel cable to connect OOPic R with my PC. Secondly, I open
compiler 5.01 and then configure cable and find delay time. After
those inital procedures, I start to program and then click "make and
download" in order to compile and download my program to OOPic R.
Then, the compiler shows the message indicating that the program has
been downloaded successfully but the OOPic board do not have any
response (yellow LED "IOLine 6" do not light anf flash).Could you
help me to fix this problem. I did post part of the Hex Code
generated from compiler on the forum. If you need it for reference, I
can send entire HEX code to you via email.
--- In oopic@yahoogroups.com, ooPIC Tech Support <dennis.clark@...>
wrote:
>
> If you compiled, but didn't download it would look like this.
Please
> give me a "blow-by-blow" account of every step that you took,
compile,
> build, download, and any messages that were given. What locale is
your
> Windows system using?
>
> DLC
>
> oscarhkw wrote:
> > --- In oopic@yahoogroups.com, "rtstofer" <rstofer@> wrote:
> >
> >> --- In oopic@yahoogroups.com, "oscarhkw" <oscarhkw@> wrote:
> >>
> >>> Hello All,
> >>>
> >>> I bought two OOPic R (firmware B2.2 +) for my research.
However, I
> >>> found that all boards cannot run the program properly. I used
> >>>
> > Windows
> >
> >>> XP and OOPic 5.01 compiler as a programming environment and
> >>>
> > followed
> >
> >>> the example:
> >>>
> >>> Dim LED as New ODio1
> >>>
> >>> Sub Main()
> >>>
> >>> OOPic.delay = 500
> >>> LED.IOLine = 6
> >>> LED.Direction = cvOutput
> >>>
> >>> Do
> >>> LED =OOPic.Hz1
> >>> Loop
> >>>
> >>> End Sub
> >>>
> >>> from the book called "Programming and customizing the OOPic
> >>> Microcontroller" in order to test one of the boards but the
> >>>
> > yellow LED
> >
> >>> does not flash after the program being downloaded. I have tried
> >>> antoher board. it also has this problem. Also, I did try "cosmic
> >>> wedgie" recovery but it still doesn't work. How can I repair
those
> >>> OOPic boards
> >>>
> >>>
> >> Which programming method did you use, parallel or serial cable?
If
> >> you used the serial cable and the device programmed successfully
(no
> >> errors from the IDE and you watched the download progress bar
move
> >> left to right) then the OOPic itself is working.
> >>
> >> With the parallel cable, programming will almost always succeed
> >> because the cable programs the EEPROM while holding the OOPic in
> >> reset. Successful programming of the EEPROM says nothing about
the
> >> state of the OOPic.
> >>
> >> Check the obvious things first: battery voltage, logic voltage
(+5
> >>
> > on
> >
> >> pin 4 of either I2C connector (the white 5 pin connectors)
relative
> >>
> > to
> >
> >> ground on pin 2. This is a different voltage regulator than the
one
> >> that supplies the outer two pins of the IO header. You might as
> >>
> > well
> >
> >> check that voltage as well - say adjacent to IOLine 1.
> >>
> >> You did install Port95NT.exe before installing the IDE, right?
> >> www.oopic.com/dloadp.html
> >>
> >> Richard
> >>
> >>
> >
> > I did install Port95NT.exe already. I tried both methods and no
error
> > message appeared but OOPic boards also cannot work properly.
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
> --
> ------------------------------------------------------
> Dennis Clark ooPIC Tech Support
> www.oopic.com
> ------------------------------------------------------
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/oopic/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/oopic/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:oopic-digest@yahoogroups.com
mailto:oopic-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
oopic-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
No comments:
Post a Comment