> Thanks for the advice Dennis. The laptop is indeed an IBM R32 ThinkPad. I've
> located the active cable schematic. Is it a product I can purchase or do I
> have to make it myself? Or is there another way to ground the existing cable
> in another way?
>
>
>
Sure, open the DB25 housing and short a few pins to either side of the
one used for ground on that cable. See the ooPIC site for how to make
the parallel port cable and Google for the parallel port pinout so you
know what pins are grounds so that you know what pins you can short
together.
DLC
> _____
>
> From: oopic@yahoogroups.com [mailto:oopic@yahoogroups.com] On Behalf Of
> ooPIC Tech Support
> Sent: Tuesday, 8 April 2008 1:45 PM
> To: oopic@yahoogroups.com
> Subject: Re: [oopic] Not a good start
>
>
>
>
>
> Mike Martin wrote:
>
>> Thanks Dennis. I got the impression that it didn't need it because the
>> website says: "In order to use the OOPic multi-language compiler with
>> Windows NT or 2000, an additional file needs to be installed.." The title
>>
> to
>
>> the section mentions XP but the lines below just say NT and 2000. Anyway
>>
> the
>
>> port driver now works but only on my PC. On my laptop however the compiler
>> can't detect the parallel cable. The port is working and I can print from
>>
> it
>
>> though. Any thoughts? There's no serial port on this laptop. Would I have
>> any success if I bought a USB-Serial converter ? I'd also need a
>>
> programming
>
>> cable that was serial I suppose.
>>
>>
>>
>>
> This is hard to characterize without a lot of data. Some parallel ports
> (IBM's quite often) use the one pin that the standard ooPIC parallel
> cable uses as a ground as a printer detect pin, so the circuit doesn't
> ground. Sometimes the port doesn't have the power to drive the
> programmer cable/EEPROM. Sometimes you just have to tell the IDE what
> parallel port to use and not let it detect. Also, if you have anything
> "driving" the parallel port it will often take control away from the
> ooPIC IDE. Examples of these "bad" drivers to the parallel port include
> these items, even if they aren't currently attached to the parallel
> port: CD-ROM drives, "Backpack" hard drives, tape backup drives and
> other esoteric things like software oscilloscopes and logic analyzers.
> Disable those drivers and the parallel port might come back.
>
> when all else fails there is a circuit in the "files" section of the
> group called "activecable.jpg" that shows how to build a cable that will
> solve all hardware related problems with parallel port ooPIC programming.
>
> DLC
>
>> _____
>>
>> From: oopic@yahoogroups. <mailto:oopic%40yahoogroups.com> com
>>
> [mailto:oopic@yahoogroups. <mailto:oopic%40yahoogroups.com> com] On Behalf
> Of
>
>> ooPIC Tech Support
>> Sent: Monday, 7 April 2008 10:41 PM
>> To: oopic@yahoogroups. <mailto:oopic%40yahoogroups.com> com
>> Subject: Re: [oopic] Not a good start
>>
>>
>>
>> Have you installed the Port95nt.exe driver? That needs to go in first
>> before the compiler so that the IDE has access to the parallel port
>> hardware. This isn't essential for anyone using a serial cable, but it
>> is essential for those using the parallel port.
>>
>> DLC
>>
>> Mike Martin wrote:
>>
>>
>>> Hello All
>>> Thanks for your answers so far. Since my last post I've downloaded and
>>> am using the ver 6 compiler on XP with an older OOPic A.2.0. I've
>>> changed to the correct device setting but when I attempt to find the
>>> parallel cable in the cable config I run into an error "Internal error
>>> in PortInp of I2CFuncs". I get the same error using a ver B.1.0 OOpic
>>> as well. I also get the error if I manually enter the correct hex
>>> value of the port I'm using as well. Is this a problem with the PC or
>>> should I just get a new OOPic? TIA. Mike.
>>>
>>>
>>> ------------------------------------
>>>
>>> Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>
>
--
------------------------------------------------------
Dennis Clark ooPIC Tech Support
www.oopic.com
------------------------------------------------------
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/oopic/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/oopic/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:oopic-digest@yahoogroups.com
mailto:oopic-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
oopic-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
No comments:
Post a Comment