batch issue since there are at least two of you that have the problem on
multiple parts. I've raised the flag at manufacturing and I'll get back
to you on how to get the units swapped for working ones as soon as the
information gets to me.
***
If anyone else has C1.1+ ooPIC parts please use this program below to
check to see if it works properly. If you get the symptoms that have
been stated here then contact the list and I'll get you in touch with
replacements too.
***
DLC
************** Program to check ooPIC C1.1+ devices
This code flashes LED 7 at a .5Hz rate if all is right..
Dim BLINK As New oEvent
Dim WIRE As New oWire
Dim led7 As New oLED
Dim led5 As New oLED
Dim flag As New oByte
Sub Main()
flag = 0
ooPIC.Delay = 500
led5.IOLine = 5
led5.TurnOn
led7.IOLine = 7
WIRE.Input.Link(WIRE.Input
WIRE.Output.WIRE.Output
WIRE.Operate = cvTrue
End Sub
Sub BLINK_Code()
If flag = 1 Then
led7.TurnOn
flag = 0
Else
led7.TurnOff
flag = 1
End If
End Sub
s.k.f. wrote:
> I just got a bunch of these too and thought I would see what mine
> would do with this code.
>
> exactly as you stated. green blinks twice. then starts blinking med
> to full intensity the comes on and stays on.
>
> using the 6.1.1 compiler and the c1.1+ chip. I bought 10 of these
> wonder if they all have the glitch
>
> some other interesting test:
>
> added line led7.TurnOn after the led7.ioline=7 and then the red one
> comes on but not as it should green still turns off and on too. both
> stop and stay on after about 6 seconds
>
> moved the oopic.delay to before the sub main() and the leds continue
> to blink, in sync then out. blinking doesn't stop however. this is
> doing something to the rx line too as the led in the usb cable rxled
> has a short flash now and then.
>
> remove the oopic.delay all together and the leds blink fast then
> stay on.
>
>
> --- In oopic@yahoogroups.com, ooPIC Tech Support <dennis.clark@...>
> wrote:
>
>> Yes,
>>
>> Replace the ooPIC C, it must have a bad version of the code in
>>
> it.
>
>> The code that I sent you works perfectly here.
>>
>> DLC
>>
>> dldlhfd@... wrote:
>>
>>>
>>> Oopic C.1.1+ Oopic C Carrier board 6.1.1 compiler
>>> To refresh your memory, I have been having trouble getting
>>>
> the events to
>
>>> work. We have sent email back and forth You sent this program
>>>
> saying that if
>
>>> it did not work then you thought my chip was broken.
>>> I tried the program and the results were:
>>> The green led comes on flashes and changes intensity and
>>>
> then stays on.
>
>>> It never goes to the subroutine to turn on the red led as it
>>>
> should.
>
>>> So I talked to the people at the Bot Shop and they arranged
>>>
> with Savage
>
>>> and sent me a new chip. The very first thing I did was put the
>>>
> chip on my
>
>>> board and try the program. It did exactly the same thing with
>>>
> the new chip as it
>
>>> did with the old. Just to make sure it was not the carrier
>>>
> board I took the
>
>>> chip off the board, put the chip on my proto board and put the
>>>
> 9 volt
>
>>> battery to pins 24 and 23. I got he exact same reaction. The
>>>
> red led in the sub
>
>>> routine never comes on.
>>> This is very frustrating. Every thing else that I have
>>>
> tried works. Do
>
>>> you have any suggestions for me?
>>>
>>> In a message dated 2/4/2008 12:09:35 A.M. Eastern Standard
>>>
> Time,
>
>>> dennis.clark@... writes:
>>>
>>> This code works, but it flashes at a .5Hz rate, I wasn't
>>>
> interested in a
>
>>> 1Hz flash so much as working event code.
>>>
>>> ---------------------------------------------------
>>> Dim BLINK As New oEvent
>>> Dim WIRE As New oWire
>>> Dim led7 As New oLED
>>> Dim led5 As New oLED
>>> Dim flag As New oByte
>>>
>>> Sub Main()
>>> flag = 0
>>> ooPIC.Delay = 500
>>> led5.IOLine = 5
>>> led5.TurnOn
>>> led7.IOLine = 7
>>> WIRE.Input.Link(WIRE.Input
>>> WIRE.Output.WIRE.Output
>>> WIRE.Operate = cvTrue
>>> End Sub
>>>
>>> Sub BLINK_Code()
>>> If flag = 1 Then
>>> led7.TurnOn
>>> flag = 0
>>> Else
>>> led7.TurnOff
>>> flag = 1
>>> End If
>>>
>>> End Sub
>>> ----------------------------------------------
>>>
>>> If this code doesn't work for you then your ooPIC is broken.
>>>
>>>
>>>
>>>
>>> **************The year's hottest artists on the red carpet at
>>>
> the Grammy
>
>>> Awards. Go to AOL Music.
>>> (http://music.aol.com/grammys?NCID=aolcmp00300000002565)
>>>
>>>
>>> [Non-text portions of this message have been removed]
>>>
>>>
>>>
>>>
>>> Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>>
>> --
>> ------------------------------------------------------
>> Dennis Clark ooPIC Tech Support
>> www.oopic.com
>> ------------------------------------------------------
>>
>>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
--
------------------------------------------------------
Dennis Clark ooPIC Tech Support
www.oopic.com
------------------------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/oopic/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/oopic/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:oopic-digest@yahoogroups.com
mailto:oopic-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
oopic-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
No comments:
Post a Comment