would do with this code.
exactly as you stated. green blinks twice. then starts blinking med
to full intensity the comes on and stays on.
using the 6.1.1 compiler and the c1.1+ chip. I bought 10 of these
wonder if they all have the glitch
some other interesting test:
added line led7.TurnOn after the led7.ioline=7 and then the red one
comes on but not as it should green still turns off and on too. both
stop and stay on after about 6 seconds
moved the oopic.delay to before the sub main() and the leds continue
to blink, in sync then out. blinking doesn't stop however. this is
doing something to the rx line too as the led in the usb cable rxled
has a short flash now and then.
remove the oopic.delay all together and the leds blink fast then
stay on.
--- In oopic@yahoogroups.com, ooPIC Tech Support <dennis.clark@...>
wrote:
>
> Yes,
>
> Replace the ooPIC C, it must have a bad version of the code in
it.
> The code that I sent you works perfectly here.
>
> DLC
>
> dldlhfd@... wrote:
> >
> > Oopic C.1.1+ Oopic C Carrier board 6.1.1 compiler
> > To refresh your memory, I have been having trouble getting
the events to
> > work. We have sent email back and forth You sent this program
saying that if
> > it did not work then you thought my chip was broken.
> > I tried the program and the results were:
> > The green led comes on flashes and changes intensity and
then stays on.
> > It never goes to the subroutine to turn on the red led as it
should.
> > So I talked to the people at the Bot Shop and they arranged
with Savage
> > and sent me a new chip. The very first thing I did was put the
chip on my
> > board and try the program. It did exactly the same thing with
the new chip as it
> > did with the old. Just to make sure it was not the carrier
board I took the
> > chip off the board, put the chip on my proto board and put the
9 volt
> > battery to pins 24 and 23. I got he exact same reaction. The
red led in the sub
> > routine never comes on.
> > This is very frustrating. Every thing else that I have
tried works. Do
> > you have any suggestions for me?
> >
> > In a message dated 2/4/2008 12:09:35 A.M. Eastern Standard
Time,
> > dennis.clark@... writes:
> >
> > This code works, but it flashes at a .5Hz rate, I wasn't
interested in a
> > 1Hz flash so much as working event code.
> >
> > ---------------------------------------------------
> > Dim BLINK As New oEvent
> > Dim WIRE As New oWire
> > Dim led7 As New oLED
> > Dim led5 As New oLED
> > Dim flag As New oByte
> >
> > Sub Main()
> > flag = 0
> > ooPIC.Delay = 500
> > led5.IOLine = 5
> > led5.TurnOn
> > led7.IOLine = 7
> > WIRE.Input.Link(WIRE.Input
> > WIRE.Output.WIRE.Output
> > WIRE.Operate = cvTrue
> > End Sub
> >
> > Sub BLINK_Code()
> > If flag = 1 Then
> > led7.TurnOn
> > flag = 0
> > Else
> > led7.TurnOff
> > flag = 1
> > End If
> >
> > End Sub
> > ----------------------------------------------
> >
> > If this code doesn't work for you then your ooPIC is broken.
> >
> >
> >
> >
> > **************The year's hottest artists on the red carpet at
the Grammy
> > Awards. Go to AOL Music.
> > (http://music.aol.com/grammys?NCID=aolcmp00300000002565)
> >
> >
> > [Non-text portions of this message have been removed]
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
> --
> ------------------------------------------------------
> Dennis Clark ooPIC Tech Support
> www.oopic.com
> ------------------------------------------------------
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/oopic/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/oopic/join
(Yahoo! ID required)
<*> To change settings via email:
mailto:oopic-digest@yahoogroups.com
mailto:oopic-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
oopic-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
No comments:
Post a Comment